1. Prepare the natural nail as usual and apply I.Am Blue Scrub to the natural nail plate. Allow to dry completely before applying I.Am by BO. Base Gel.

2. I.Am by BO. Base Gel - Wipe the brush on the neck of the bottle to remove excess product. Seal the free edge of the nail to ensure durability and prevent the product from shrinking. Hold the brush horizontally on the nail and apply a thin layer of I.Am by BO. Base Gel over the entire nail, from the cuticle to the free edge. Cure all four fingers together for 120 sec. UV / 30 sec. LED. Repeat the process on the other hand and then on the thumbs. Optional: brush with a clean gel brush to remove excess sticky cured base gel to reduce the chance of shrinkage and to apply a smoother color.

3. I.Am Collection by BO. Gelpolish - Rub the bottle upside down between the palms of your hands to ensure that the color/pigment is well mixed. Seal the free edge with I.Am Collection by BO. Gelpolish to ensure durability and prevent color shrinkage. Hold the brush horizontally on the nail and continue toward the center of the nail. Move the brush from the center of the nail upward toward the proximal nail fold, then stroke downward toward the free edge. Make sure the gel polish does not get on the skin. If the nail polish has touched the skin, remove it before curing the nail with I.Am UV Cleanser and Cuticle Pusher. Cure all four nails for 120 sec. UV / 30 sec. LED. Repeat the process on the other hand and thumbs.

4. I.Am Collection by BO. Gel Polish - Apply a second thin coat of nail polish following the same steps. This coat ensures full coverage when using an opaque color. NOTE: If you have a dark complexion or are using a different lamp, you may need to cure twice to ensure the color is fully cured and does not bleed into your Top Gel application.

5. I.Am by BO. Top Gel - Wipe the brush on the neck of the bottle to remove excess product. Place a cap on the free edge of the nail to ensure shelf life and prevent the product from shrinking. Hold the brush horizontally on the nail and apply a thin layer of I.Am by BO. Top Gel to each nail surface of all four nails on one hand. Cure all four nails for 120 sec. UV / 30 sec. LED. Repeat on the other hand and finish by applying to the thumbs.

6. If you are using I.Am by BO. Sticky Top Gel, it will be necessary to clean the sticky layer after curing. Saturate a gel sponge with I.Am UV Cleanser. Wipe away the top sticky layer (this is the sticky inhibition layer) with light pressure. NOTE: Do not wipe the nail again with a used part of the gel sponge, as this will redistribute the sticky layer, causing the Top Gel to become dull. Use a clean saturated gel sponge for each finger. Tip: Wait to clean (about 1 minute) after curing to allow the nails to “cool down” for even more shine.

Removal

1. Remove the seal on each nail with an I.Am 180/180 Grit file. Saturate a Nail Foil with I.Am Soakable Gel Remover and secure the foil tightly around the finger.
2. Leave the Nail Foil on the finger for ten minutes. Pull the Nail Foil and product off the fingernail with a twisting motion.
3. If necessary, carefully remove any excess Gel Polish using a Cuticle Pusher. Be careful not to damage the surface layers of the natural nail plate.

Bis-HEA Poly(1,4-Butanediol)-9/IPDI Copolymer, Hydroxypropyl Methacrylate, Sucrose Benzoate, Trimethylolpropane Trimethacrylate, Bis-HEMA Polyneopentyl Glycol Adipate/IPDI Copolymer, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Cyclohexane​

[/content-bottom]